What are the characteristics of aluminum-plastic panels? Matters needing attention in the use of aluminum-plastic panels

Aluminum-plastic panel, also known as aluminum-plastic composite panel, is made of multi-layer materials, the upper and lower tubes are high-purity aluminum alloy panels, and the middle is low-space polyethylene board, which is combined with glue point agent. Decorative materials, many people don't know much about aluminum panels. Today, let Xiaobian take Dahao to understand the characteristics of the lower pot plate and a brief introduction to the precautions for the use of aluminum-plastic panels. I hope it will be helpful to you. .

What are the characteristics of aluminum composite panel

1. Super strong to height:

The aluminum veneer adopts a new process, which improves the most critical lifting index of the aluminum veneer to a polar state, so that the flat laying and weather resistance performance of the aluminum veneer is correspondingly improved.

2. Material light suspension processing

The mass of the aluminum composite panel per square meter is only about 35-5.5kg, and it is easy to handle. Because of its superior construction, it can be cut, cut, cut, edged, and bent into industrial shapes with only simple woodworking tools. , The various shapes of the vertical angle may cooperate with the designer to make various superimpositions, install simple invasion, snap shots, and reduce the release of the ball.

3. Excellent fire performance:

The middle of the aluminum-plastic panel is the PE plastic core material that blocks the end, and the two layers are extremely difficult to burn, so it is a safe fireproof material that meets the fire resistance requirements of building regulations.

4. Impact resistance:

It has strong impact resistance, high toughness, no damage to the surface when bending, and impact resistance. It has a high safety factor in home decoration, and is especially suitable for families with children at home.

5. Super durability;

Due to the use of PVDF based on KYNAR-500, there are unique concerns in terms of the most economical and durable aspects. It can maintain its beautiful appearance for up to 20 years in mild sunlight.

6. Coating uniform groove:

Variety of colors After chemical treatment and Henkel film technology, the adhesion between the paint and the aluminum watch panel is uniform, and the variety of colors makes the selection space larger and shows the individuality of the home.

The above is a brief introduction to the characteristics of the aluminum lookout board. I believe that after the above introduction, everyone will have a further understanding and understanding of the lookout board. Of course, although the lookout board has many advantages, it has a good decorative effect and a wide range of use. However, in order to ensure that its advantages can be fully demonstrated during its use, the editor reminds everyone that the precautions in the use process are indispensable. What are the precautions for the use of aluminum watch panels? Let's take a look at the following introduction:

Precautions for the use of aluminum composite panels:

1. Aluminum-plastic panels should be stored in an appropriate way or installed in a dry and ventilated place to avoid accumulation of water, and the ambient temperature should not be higher than 70C, and avoid installation in abnormal environments, such as smoke, dust, wind and sand, radiation, and striking gas. and chemical environment.

2. Aluminum-plastic panels should be placed flat during transportation or storage. When transporting, the 4 sides of the board must be lifted at the same time, and one side should be dragged in a hurry. so as not to scratch the surface of the board.

3. When grooving with a love machine or a gong machine, a round head or z90, V-shaped flat head or iron knife should be used to make the groove, and the 02-03mm plastic core board should be left with the side board to bend the edge to increase the Strong health and toughness, as well as preventing oxidation of the aluminum sheet, too sharp corners or cutting damage to the lead panel or leaving the Chinese material too thick will cause the button panel to break or the paint to peel off when the edge is bent.

4. When bending the edge, it is necessary to use even force, forming at one time, do not fold it repeatedly, otherwise the aluminum panel will be broken,

5. In order to maintain the flatness of the aluminum-plastic panel and enhance its wind resistance, the aluminum-plastic panel needs an inner skeleton after being bent and glued to the board.

6. When it is used for the decoration of the curved surface, the aluminum-plastic panel should be bent by the electric bending equipment, and the force should be gradually applied to make the panel gradually reach the required curved surface, and the cutting should be done in one step.

7. Install the aluminum watch panel on the same plane in the same process direction, otherwise it may cause a difference in viewing angle

8. After the aluminum composite panel is installed, the protective film should be removed within 45 days. Otherwise, the protective film will be aged due to long-term exposure to the sun, and may cause glue retention when torn.

9. The inner wall panel should be used indoors and should not be installed outdoors to ensure its service life.

10. If the surface of the board is polluted during construction or use, it can be gently cleaned with neutral detergent or alcohol, and strong acid and strong detergents should not be used for cleaning.

Aluminum composite panel

The above is a brief introduction to the characteristics of the aluminum composite panel and the precautions for the use of the photo film. I hope it will be helpful to everyone.